Request Medical Evacuation Outline

Request Medical Evacuation Outline Essay Sample

Conditions: You have a casualty requiring medical evacuation (MEDEVAC) and you will need a patient pickup site. You will need operational communications equipment, MEDEVAC request format, a standard scale military map, a grid coordinate scale, and unit signal operation instructions (SOIs).

Standards: Transmit a MEDEVAC request, providing all necessary information within 25 seconds. Transmit, as a minimum, line numbers 1 through 5 during the initial contact with the evacuation unit. Transmit lines 6 through 9 while the aircraft or vehicle is en route, if not included during the initial contact.

Risk Assessment: Low

Environmental and Safety Concerns: Be cautious of furniture and electric plugs.

Evaluation: GO / NO-GO


1. Collect all applicable information needed for the MEDEVAC request.

a. Determine the grid coordinates for the pickup site.

b. Obtain radio frequency, call sign, and suffix.

c. Obtain the number of patients and precedence.

d. Determine the type of special equipment required.

e. Determine the number and type (litter or ambulatory) of patients.

f. Determine the security of the pickup site.

g. Determine how the pickup site will be marked.

h. Determine patient nationality and status.

i. Obtain pickup site nuclear, biological, and chemical (NBC) contamination information, normally obtained from the senior person or medic. Note: NBC line 9 information is only included when contamination exists.

2. Record the gathered MEDEVAC information using the authorized brevity codes. (See table 081-831-0101-1.) Note: Unless the MEDEVAC information is transmitted over secure communication systems, it must be encrypted, except as noted in step 3b(1).

a. Location of the pickup site (line 1).

b. Radio frequency, call sign, and suffix (line 2).

c. Numbers of patients by precedence (line 3).

d. Special equipment required (line 4).

e. Number of patients by type (line 5).

f. Security of the pickup site (line 6).

g. Method of marking the pickup site (line 7).

h. Patient nationality and status (line 8).

i. NBC contamination (line 9).

3. Transmit the MEDEVAC request. (See STP 21-1-SMCT, task 113-571-1022.)

a. Contact the unit that controls the evacuation assets.

(1) Make proper contact with the intended receiver.

(2) Use effective call sign and frequency assignments from the SOI.

(3) Give the following in the clear “I HAVE A MEDEVAC REQUEST;” wait one to three seconds for a response. If no response, repeat the statement.

b. Transmit the MEDEVAC information in the proper sequence.

(1) State all line item numbers in clear text. The call sign and suffix (if needed) in line 2 may be transmitted in the clear. Note: Line numbers 1 through 5 must always be transmitted during the initial contact with the evacuation unit. Lines 6 through 9 may be transmitted while the aircraft or vehicle is en route.

(2) Follow the procedure provided in the explanation column of the MEDEVAC request format to transmit other required information.

(3) Pronounce letters and numbers according to appropriate radio/telephone procedures.
(4) Take no longer than 25 seconds to transmit.

(5) End the transmission by stating “Over.”

(6) Keep the radio on and listen for additional instructions or contact from the evacuation unit.


Setup: Evaluate this task during a training exercise involving a MEDEVAC aircraft or vehicle, or simulate it by creating a scenario and providing the information as the Soldier requests it. You or an assistant will act as the radio contact at the evacuation unit during “transmission” of the request.
Give a copy of the MEDEVAC request format to the Soldier.

Brief Soldier: Tell the Soldier to prepare and transmit a MEDEVAC request. State that the communication net is secure.


1. Collected all information needed for the MEDEVAC—— —— request line items 1 through 9

2. Recorded the information using the authorized brevity—— —— codes.

3. Transmitted the MEDEVAC request within 25 seconds.—— ——